<![CDATA[Cervenka Consulting Forums — unable to mesh cylinder]]> https://forums.cervenka.cz/viewtopic.php?id=2257 Tue, 08 Jun 2021 05:51:54 +0000 PunBB <![CDATA[Re: unable to mesh cylinder]]> https://forums.cervenka.cz/viewtopic.php?pid=4844#p4844 Dear Pavlo and Mohmad
Followed the suggestion, I could mesh the cylinder with holes. Thanks.
While running analysis I got the following message. ,

Error in command ElemsMatProp
Error in base file 'C:/Program Files/GiD/GiD 14.0/problemtypes/Atena/Execute/../include.src.bas/Write_Clasic_Bar_Element.bas' at line number 10: Error into an *if expression

When I searched in forum, I noticed, Pavlo faced similar problem.

How should I correct. My reinforcement bar does not have contact with concrete when it runs through holes. Is it the reason?
Can you / anyone help.
Thank you

]]> Tue, 08 Jun 2021 05:51:54 +0000 https://forums.cervenka.cz/viewtopic.php?pid=4844#p4844 <![CDATA[Re: unable to mesh cylinder]]> https://forums.cervenka.cz/viewtopic.php?pid=4843#p4843 If you have cylinder volume and you need to be structured with Hexahedra, you need to have 6 surfaces 1top,1bottom, and 4 sides so divide your side surfaces
If you need help send us your model to Cervenka@cervenka.cz

Thanks,
Mohamad

]]> Fri, 04 Jun 2021 10:25:00 +0000 https://forums.cervenka.cz/viewtopic.php?pid=4843#p4843 <![CDATA[Re: unable to mesh cylinder]]> https://forums.cervenka.cz/viewtopic.php?pid=4842#p4842 Also you can share your model and I can record a video how to make unstructured mesh

]]> Thu, 03 Jun 2021 10:03:55 +0000 https://forums.cervenka.cz/viewtopic.php?pid=4842#p4842 <![CDATA[Re: unable to mesh cylinder]]> https://forums.cervenka.cz/viewtopic.php?pid=4841#p4841 Thank you.
Yes, I am using GiD.
I will search in GiD forum.

]]> Thu, 03 Jun 2021 09:20:14 +0000 https://forums.cervenka.cz/viewtopic.php?pid=4841#p4841 <![CDATA[Re: unable to mesh cylinder]]> https://forums.cervenka.cz/viewtopic.php?pid=4839#p4839 Are you using GiD?
Structured type can only be assigned to a 6-side prism.
You have to use semi-structured instead.

Also you can check GiD forum for such kind of problems.

]]> Mon, 31 May 2021 18:40:49 +0000 https://forums.cervenka.cz/viewtopic.php?pid=4839#p4839 <![CDATA[unable to mesh cylinder]]> https://forums.cervenka.cz/viewtopic.php?pid=4837#p4837 "Volume number 1 cannot be meshed with the assigned element type, unstructured volumes can only be meshed with tetrahedra, points or sphere elements."
Volume number 1 is a cylinder of 150mm dia 150mm height, with 20mm dia x 50mm high holes , one at top and at bottom. I tried structured line with 16 divisions and 0.05 mesh size. I am trying to model pullout test.
can anyone help me?
Thanks

]]> Sun, 30 May 2021 05:42:03 +0000 https://forums.cervenka.cz/viewtopic.php?pid=4837#p4837