• Registered: 2019-05-21
  • Posts: 16

Topic: How to accelerate the analysis time in ATENA Engineering 3D

Hi

I hope this message finds u well,

My model is continuous beam strengthened with an advanced material, when i did that, it took a long time to make analysis and i considered all the points in Troubleshooting Manual 2.2.17 except the symmetry point. So, i can simulate my beam and study that with the half shape, but in that case, the middle support at the half total length, i put at the end of the half shape to know the program that there is a support here after symmetry, or identify the surface at the end of the symmetric part with the same characterestics of the middle support (restrained in x,y,z) instead using the support. please reply to me asap.

Thanks

Quote Post 1

  • dpryl
  • CC software developer
  • Offline
  • Registered: 2007-07-13
  • Posts: 1,107

Re: How to accelerate the analysis time in ATENA Engineering 3D

Dear ahmed, please see also Troubleshooting, 2.4.1 Out of memory error during ATENA analysis for additional tips. Regarding symmetry, please first see the Tutorial example (Shear Beam).

From your description it is not clear if the symmetry in 1/2 length makes sense - please keep in mind that both the geometry and supports+loads need to be symmetrical to allow a valid 1/2-symmetry modelling.

You can follow Troubleshooting, 2.1.1 to send us your model along with some sketches etc. such that we can advice on your particular modelling.

Regards.

dpryl's Website

Quote Post 2

  • Registered: 2019-05-21
  • Posts: 16

Re: How to accelerate the analysis time in ATENA Engineering 3D

Hi

I tracked the steps needed to send my model, and already i did, but for the large size, i shared it using the dropbox with u. So please see and reply to me ASAP.

Thanks in advance

Quote Post 3

  • Registered: 2019-05-21
  • Posts: 16

Re: How to accelerate the analysis time in ATENA Engineering 3D

Hi

i want to inform u that till now i don`t receive any reply to my question after sending the model to u. Please I`m looking forward u reply asap.

Thanks

Quote Post 4

  • dpryl
  • CC software developer
  • Offline
  • Registered: 2007-07-13
  • Posts: 1,107

Re: How to accelerate the analysis time in ATENA Engineering 3D

Dear Ahmed, please check your spam folder - maybe the filter settings are a bit too aggresive?

My colleague, Zdenek Janda, has answered on 11.6.2019 at 8:33, with Subject: Fwd: Ahmed Mandor shared "Inquiry file" with you

Regards.

dpryl's Website

Quote Post 5

  • Registered: 2019-05-21
  • Posts: 16

Re: How to accelerate the analysis time in ATENA Engineering 3D

Hi,

Thanks for u interest and reply, but i didn't find any response, please if possible, direct the answer again in the drobpox, because i searched about that and found the files that attached to u to check, were deleted by Zdenek, so, please help me in that and thanks for u time again,

Thanks in advance

Quote Post 6

  • dpryl
  • CC software developer
  • Offline
  • Registered: 2007-07-13
  • Posts: 1,107

Re: How to accelerate the analysis time in ATENA Engineering 3D

Dear Ahmed, I have re-sent the answer from June 11th - please check your mail again, including the spam folder. If you still can not get to the answer, I suggest to contact us from another email such that we can re-send the message there.
Regards.

dpryl's Website

Quote Post 7

  • Registered: 2019-05-21
  • Posts: 16

Re: How to accelerate the analysis time in ATENA Engineering 3D

Hi

unfortunately i'm not found any thing, so please forward the response on (ahmedmandor134@yahoo.com) if possible.

Thanks for u help

Quote Post 8

  • dpryl
  • CC software developer
  • Offline
  • Registered: 2007-07-13
  • Posts: 1,107

Re: How to accelerate the analysis time in ATENA Engineering 3D

I have re-sent it again.

dpryl's Website

Quote Post 9